Rockwell-automation 900 Temperature Controller Communications Function Bedienungsanleitung PDF herunterladen (Seite 54)

Publication 900-UM004D-EN-E - July 2010

3-12 Communications Data

C3 (83) 0071 Monitor/Setting Item

H’00000000...H’0000000F (0 ...5)

* Same as for Monitor/Setting Item 1.

Advanced

function

settingC3 (83) 0072 Monitor/Setting Item

H’00000000...H’0000000F (0 ...5)

* Same as for Monitor/Setting Item 1.

C3 (83) 0073 PV/SP Display Screen

Selection

H’00000000 (0): PV/SP

H’00000001 (1): PV/SP/Multi-SP

PV/SP/MV

H’00000002 (2): PV/SP/MV

PV/SP/Multi-SP

H’00000003 (3): PV/SP/Multi-SP

H’00000004 (4): PV/SP/MV

H’00000005 (5): PV/SP/Multi-SP

PV/SP/Soak Time Remain

H’00000006 (6): PV/SP/MV

PV/SP/Soak Time Remain

H’00000007 (7): PV/SP/Soak Time Remain

C3 (83) 0074 MV Display Screen

Selection

H’00000000 (0): OFF (heating)

H’00000001 (1): ON (cooling)

C3 (83) 0075 PV Decimal Point

Display

H’00000000 (0): OFF

H’00000001 (1): ON

C3 (83) 0076 PV Status Display

Function

H’00000000 (0): OFF

H’00000001 (1): Manual

H’00000002 (2): Stop

H’00000003 (3): Alarm 1

H’00000004 (4): Alarm 2

H’00000005 (5): Alarm 3

H’00000006 (6): Alarm 1 to 3 OR status

H’00000007 (7): Heater alarm

C3 (83) 0077 SV Status Display

Function

H’00000000...H’00000006 (0...7)

* Same as for PV Status Display Function

C3 (83) 0078 Control Output 1

ON/OFF Count Alarm

Set Value

H’00000000...0000270F (0...9999)

C3 (83) 0079 Control Output 2

ON/OFF Count Alarm

Set Value

H’00000000...0000270F (0...9999)

C3 (83) 0083 Display Refresh

Period

H’00000000 (0): OFF

H’00000001 (1): 0.25

H’00000002 (2): 0.5

H’00000003 (3): 1.0

Table 3.3 Variable Type C3 (83)

Variable

Typ e

Address Item (Parameter) Set (Monitor) Value Function

Group

➊ The input type can be selected to march the connected sensor. There are two input types specifications:

Thermocouple/Resistance thermometer input and Analog input.

➋ The parameter will not be shown on the Controller display when alarm 3 is not assigned to an output.

➌ Communications parameters are enabled after they have been changed by resetting the controller.

➍ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 1

or 2

➎ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 2.

➏ PRST (program start) can be set even when the program pattern is set to OFF, but the function will be disabled.

➐ The logic of CompoWay/F (900-TC) operation command code 00 (communications writing) is not affected.

➑ The setting (monitor) range depends on the transfer output type setting. (See the setting data list for details.)

➒ P.END (program end output) can be set even when the program pattern is set to OFF, but the

function will be disabled.

➓ The output turns ON when the status of either the Control Output 1 ON/OFF Count Alarm or the Control Output 2 ON/OFF

Count Alarm turns ON.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 102 103

Kommentare zu diesen Handbüchern

Keine Kommentare

Rockwell-automation 900 Temperature Controller Communications Function Bedienungsanleitung Seite 54

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Rockwell-automation 900 Temperature Controller Communications Function