Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining Bedienungsanleitung Seite 88
- Seite / 278
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
88 Rockwell Automation Publication IASIMP-QS034A-EN-P - October 2012
Chapter 4 GuardLogix Configuration
3. Configure the new controller.
a. From the Type pull-down menu,
choose the controller type.
b. From the Revision pull-down
menu, choose the revision.
c. Type the file name in the Name
field.
d. From the Chassis Type pull-down
menu, choose the chassis.
e. Enter the Logix processor slot
(leftmost slot = 0).
4. Click OK.
5. From the Edit menu, choose
Controller Properties.
The Controller Properties dialog
box opens.
6. Click the Date/Time tab.
7. Check Enable Time
Synchronization.
This enables time
synchronization for the
controller.
8. Click OK.
- Accelerator Toolkit 1
- Important User Information 2
- Chapter 7 3
- Where to Start 4
- Chapter 4 6
- GuardLogix Configuration 6
- Chapter 5 6
- Appendix D 9
- Configuration 9
- Table of Contents 10
- Introduction 11
- Conventions 12
- Required Software 12
- Additional Resources 13
- FANUC CNC Express Software 19
- System Layout and Wiring 29
- • The 07_PLC_1791DS_IB16 and 32
- Project Drawings folder 33
- Edit FANUC CNC Drawing Set 34
- Edit CNC Power Drawings 35
- • 16_CNC_Ethernet_Switch 41
- • 18_CNC_Cable_Connections 41
- CNC Subpanel Layout Drawing 43
- CNC Enclosure Layout Drawing 43
- Drive Power Example 44
- Drive I/O Example 44
- System Layout Example 44
- FANUC CNC Configuration 47
- Parameter Write Enable 49
- High Speed Ethernet Option 51
- Configure Ethernet Module 53
- Create a New Project File 56
- 5. Select the model 58
- USB External Device 63
- EtherNet/IP Settings 64
- Logic Configuration 68
- P0001 (OP Panel Path 1) 71
- P0005 (Machine Sequence) 71
- P0010 (Window Functions) 72
- P0023 (Alarm Routine) 72
- Device Logic Modules 73
- 4. Click to save your FANUC 76
- LADDER III application file 76
- Figure 8 - Logic Modules 81
- Order and Run the DMAT Wizard 84
- Save the Project File 90
- 9. Click OK 94
- FANUC CNC AOP Configuration 95
- Add and Configure FANUC CNC 96
- The Import Configuration 101
- Import 105
- Machining Example 109
- Drill CNC Example 109
- Gantry Y Axis Drive Example 110
- Machine CNC Example 110
- Gantry X Axis Drive Example 110
- • Drill CNC 111
- • Machining CNC 111
- • Gantry X Axis Drive 111
- • Gantry Y Axis Drive 111
- IMPORTANT 113
- _ModuleNameXX tag 116
- Logic Placeholder 121
- Safety Logic Integration 137
- GuardLogix Safety Logic 138
- Safety Faceplate Logic 144
- Before You Begin 149
- What You Need 149
- Follow These Steps 150
- Delete Unused Displays 154
- Delete Unused Parameter Files 155
- Configure Parameter Files 156
- Parameters 157
- Comments 157
- Chapter 6 158
- • SafeIOAlarmTrigger 160
- • ModuleAlarmTrigger 160
- • CNCAlarmTrigger 160
- • CIPMotionAlarmTrigger 160
- Add Parameter Files 165
- Parameters folder 166
- Import Alarm Setup File 171
- • SaveIOAlarmTrigger 173
- Import and Edit Alarm Tags 174
- Goto Display Buttons 189
- CellGuard1 193
- System Commissioning 195
- Download Applications 197
- Terminal 202
- Commissioning Devices 205
- Verify Network Communication 206
- 1756-EN2TR 207
- EtherNet/IP 207
- • If there is an active 211
- Clearing Faults 212
- Operator (manual) Control 212
- Program (automatic) Control 213
- System Application Guide 215
- Machine Startup Faceplate 217
- Machine Control 219
- Program/Operator Mode 219
- CNC Faceplate 221
- CNC Status Views 222
- CNC Control Views 222
- Fault Indication View 223
- Fault Diagnostic Views 224
- Configuration View 225
- Guard I/O Safety Faceplates 226
- Logic Program Overview 229
- Module Routine Overview 231
- Machine Module 234
- Machine Control Module Tags 236
- Application Modules 240
- Device Modules 241
- Logic Module Customization 243
- • Mode = UDT_MachMode 244
- • Command = UDT_MachCmd 244
- • State = UDT_MachState 244
- (2) Refer to Chapter 5 246
- Module Fault Customization 249
- Appendix 255
- Add Optional Faceplate Views 258
- Verify Your IP Address 262
- Load the Controller Firmware 265
- Assign IP Addresses 267
- Numerics 271
- Rockwell Automation Support 278
- Documentation Feedback 278
Verwandte Produkte und Handbücher für Ausrüstung Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining
(4 Seiten)
Ausrüstung Rockwell-automation SP120 ACDrive 115VAC, 1Ph, 230VAC, 1Ph/3Ph, 1/4-5. Bedienungsanleitung
(210 Seiten)
(210 Seiten)
Ausrüstung Rockwell-automation MDO16GNS 16-Channel Digital Output Module 48Vdc Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Ausrüstung Rockwell-automation T8451 Trusted Industrial Control System Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Ausrüstung Rockwell-automation T8480 Trusted TMR Analogue Output Module Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Ausrüstung Rockwell-automation 1440-REX03-04RG XM-442 Voted EODS Relay Module Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Ausrüstung Rockwell-automation T7454 ICS Regent+Plus AC Isolated Digital Output M Bedienungsanleitung
(13 Seiten)
(13 Seiten)
Ausrüstung Rockwell-automation TDI16EIA 16-Channel Digital Input Termination Card Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Ausrüstung Rockwell-automation 2097-V3xPRx-LM Kinetix 300 and Kinetix 350 Drive S Bedienungsanleitung
(84 Seiten)
(84 Seiten)
Ausrüstung Rockwell-automation WebPak 3000 DC Drives Hardware Reference, Install Bedienungsanleitung
(92 Seiten)
(92 Seiten)
Ausrüstung Rockwell-automation Drives and Motion Accelerator Toolkit Quick Start Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Ausrüstung Rockwell-automation T8423 Trusted TMR 35 - 120 Vdc Digital Input Modul Bedienungsanleitung
(33 Seiten)
(33 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern