Rockwell-automation 20-COMM-M Modbus/TCP Adapter Bedienungsanleitung Seite 59
- Seite / 98
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Troubleshooting 5-7
20-COMM-M Modbus/TCP Adapter User Manual
Publication 20COMM-UM014C-EN-P
Events
Many events in the event queue occur under normal operation. If you
encounter unexpected communications problems, the events may help you
or Allen-Bradley personnel troubleshoot the problem. The following events
may appear in the event queue:
Table 5.B Adapter Events
Code Event Description
1 No Event Empty event queue entry.
2 DPI Bus Off Flt A bus-off condition was detected on DPI. This event may be caused by loose or broken cables or by noise.
3 Ping Time Flt A ping message was not received on DPI within the specified time.
4 Port ID Flt The adapter is not connected to a correct port on a DPI product.
5 Port Change Flt The DPI port changed after start up.
6 Host Sent Reset The drive sent a reset event message.
7 EEPROM Sum Flt The EEPROM in the adapter is corrupt.
8 Online @ 125kbps The adapter detected that the drive is communicating at 125 kbps.
9 Online @ 500kbps The adapter detected that the drive is communicating at 500 kbps.
10 Bad Host Flt The adapter was connected to an incompatible product.
11 Dup Port Flt Another peripheral with the same port number is already in use.
12 Type 0 Login The adapter has logged in for Type 0 control.
13 Type 0 Time Flt The adapter has not received a Type 0 status message within the specified time.
14 DL Login The adapter has logged into a Datalink.
15 DL Reject Flt The drive rejected an attempt to log in to a Datalink because the Datalink is not supported or is used by another
peripheral.
16 DL Time Flt The adapter has not received a Datalink message within the specified time.
17 Reserved Not used.
18 Control Disabled The adapter has sent a “Soft Control Disable” command to the drive.
19 Control Enabled The adapter has sent a “Soft Control Enable” command to the drive.
20 Message Timeout A Client-Server message sent by the adapter was not completed within 1 sec.
21 Flt Cfg Error One of the Flt Cfg xx parameters is set to a value greater than 65535 and the drive requires a 16-bit value.
22 App Updated Startup sequence detected new application firmware.
23 EN Comm Flt The adapter detected a communications fault on the network.
24 EN Sent Reset The adapter received a reset from the network.
25 EN Close Flt An I/O connection from the network to the adapter was closed.
26 EN Idle Flt The adapter is receiving “idle” packets from the network.
27 EN Open An I/O connection from the network to the adapter has been opened.
28 EN Timeout Flt An I/O connection from the network to the adapter has timed out.
29 PCCC IO Close The device sending PCCC Control messages to the adapter has set the PCCC Control Timeout to zero.
30 PCCC IO Open The adapter has begun receiving PCCC control messages (the PCCC Control Timeout was previously set to a
non-zero value).
31 PCCC IO Time Flt The adapter has not received a PCCC Control message for longer than the PCCC Control Timeout.
32 Watchdog T/O Flt The software detects a failure.
33 EEPROM Init Startup sequence detected a blank EEPROM map revision.
34 Normal Startup The adapter successfully started up.
35 Manual Reset The adapter was reset by changing its Reset Module parameter.
36 EN Link Down The Ethernet link was removed from the adapter.
37 EN Link Up An Ethernet link is available for the adapter.
38 BOOTP Response The adapter received a response to its BOOTP request.
39 Dup IP Addr The adapter uses the same IP address as another device on the network.
40-41 Reserved Not used.
42 Email Failed The adapter encountered an error attempting to send a requested e-mail message.
43-48 Reserved Not used.
- 20-COMM-M Modbus/TCP Adapter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 7
- Rockwell Automation 8
- Conventions Used in This 8
- Getting Started 9
- Features 10
- Compatible Products 10
- Required Equipment 11
- Safety Precautions 11
- 1-4 Getting Started 12
- Quick Start 13
- Status Indicators 14
- Installing the Adapter 15
- Setting the Web Pages 16
- Connecting the Adapter to 17
- Applying Power 20
- Commissioning the Adapter 22
- Configuring the Adapter 23
- Using the PowerFlex 7-Class 24
- Using BOOTP 25
- Configuring the Adapter 3-5 27
- Setting the IP Address 28
- Subnet Mask, and Gateway 28
- Setting the Data Rate 30
- Setting the I/O 30
- Configuration 30
- Setting a Communication 31
- Fault Action 31
- Setting the Message I/O 32
- Setting Web Access Control 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Flash Updating the Adapter 35
- 3-14 Configuring the Adapter 36
- Chapter 4 37
- Unit Identifier (Port Number) 38
- Using the I/O 39
- Par. 82 - [Maximum Speed] 42
- Accessing Device Parameters 45
- Direct Access Method 45
- Indirect Access Method 46
- Using Datalinks 48
- Rules for Using Datalinks 48
- Reading Datalinks 48
- Writing Datalinks 49
- Conversion Example: 50
- Supported Modbus 51
- Registers 51
- Chapter 5 53
- PORT Status Indicator 54
- MOD Status Indicator 54
- NET A Status Indicator 55
- NET B Status Indicator 55
- Viewing Adapter Diagnostic 56
- Viewing and Clearing 58
- Table 5.B Adapter Events 59
- 5-8 Troubleshooting 60
- Chapter 6 61
- Process Display Pop-up 64
- TCP/IP Configuration Web 65
- Configure E-mail 66
- Notification Web Page 66
- DPI Device Information 69
- Kit (20-XCOMM-DC-BASE) 73
- Specifications 75
- Environmental 76
- Regulatory Compliance 76
- Adapter Parameters 77
- B-6 Adapter Parameters 82
- Logic Command/Status Words 83
- Logic Status Word 84
- PowerFlex 700S Drives 85
- Glossary 87
- G-2 Glossary 88
- F Fault Action 89
- G Gateway 89
- H Hardware Address 89
- I I/O Data 90
- L Logic Command/Logic Status 91
- M Modbus/TCP Network 91
- N NVS (Non-Volatile Storage) 91
- R Reference/Feedback 92
- S Status Indicators 92
- Z Zero Data 92
- May, 2010 98
Verwandte Produkte und Handbücher für Ausrüstung Rockwell-automation 20-COMM-M Modbus/TCP Adapter
Ausrüstung Rockwell-automation 140EX-JE2_JE3 Molded Case Circuit Breaker Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Ausrüstung Rockwell-automation 140G-R-EA1TA Electrical Signalling of Overcurrent Bedienungsanleitung
(3 Seiten)
(3 Seiten)
Ausrüstung Rockwell-automation 56AMXN ControlLogix/AutoMax/Communication/Module Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Ausrüstung Rockwell-automation 57RF RFID ICODE Handheld Interface User Manual Bedienungsanleitung
(112 Seiten)
(112 Seiten)
Ausrüstung Rockwell-automation 140G_MG- General Warning for Trip Units Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Ausrüstung Rockwell-automation 22-HIM-C2S PowerFlex 4-Class Remote Small HIM Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Ausrüstung Rockwell-automation 20P PowerFlex DC Drive - Frame D Field Dual Diode Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Ausrüstung Rockwell-automation 20D PowerFlex 700S Auxiliary Control Power Supply Bedienungsanleitung
(4 Seiten)
(4 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern