Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog Bedienungsanleitung Seite 67
- Seite / 164
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Publication 1794-UM065B-EN-E - September 2010
1794-IF8IH and 1794-OF8IH Configuration 55
HART Loop Status (8 of 8 bits):
This byte indicates the Status of the HART loop from the I/O modules point
of view. This byte is generated by the I/O module itself and not from the
HART FD.
HART PV Status (8 of 8 bits):
This byte indicates the status of the HART variables (primary, secondary, third
and fourth).
HART Loop Status
HART Loop Status
Bit 0
(1)
HCS_COMM_ENABLED, HART is enabled on this channel.
Range: 0 = HART not enabled on this channel, 1 = HART enabled on this channel
(1)
HCS — HART Communications State machine
Bit 1 HCS_CONNECTED, A connection has been established with this device.
Range: 0 = no HART connection on this channel, 1 = HART connection on this
channel
Bit 2 HCS_RESPONSE_ERROR, A HART message attempt ended in failure.
Range: 0 = no HART message failures, 1 = HART message attempt failed
Bit 3 HCS_CMD48_UPDATE, Extended HART status (Command 48) was updated.
Range: 0 = extended HART status (Command 48) was not updated, 1 = extended
HART status (Command 48) was updated
Bit 4 HCS_ILOOP_TOLERANCE, HART Current Fault loop current fault.
Range: 0 = no HART Current Fault loop current fault, 1 = HART Current Fault loop
current fault
Bit 5 HART_update, The HART Field Device data for the channel has been updated
since last read.
Range: 0 = no HART FD data update, 1 = new HART FD data available
Bit 6 HART_Message, The channel's HART message queue has completed a message
since request has been received.
Range: 0 = no HART message has completed, 1 = a HART message has completed
Bit 7 Reserved
HART PV Status
Bit 0 The primary variable for this channel has been acquired.
Bit 1 The secondary variable for this channel has been acquired.
Bit 2 The third variable for this channel has been acquired.
Bit 3 The fourth variable for this channel has been acquired.
Bit 4 Reserved
- Analog Modules 1
- Important User Information 2
- Summary of Changes 3
- Related Documentation 5
- Table of Contents 7
- 1794-IF8IH and 1794-OF8IH 8
- Table of Contents iii 9
- Table of Contents v 11
- What FLEX I/O Analog 13
- Modules Do 13
- Communicate with 14
- Programmable Controllers 14
- Physical Features of 15
- Your Module 15
- Use Alarms on the Input 15
- Overrange Alarm 16
- Underrange Alarm 16
- Remote Fault Alarm 16
- Local Fault Alarm 17
- Use the HART Capabilities 18
- HART Implementation 18
- Features 19
- Select Your Analog Input 20
- Module Operating Features 20
- Data Format 21
- Select Your Analog Output 22
- Latch Mode 23
- Global Reset 23
- Diagnostic Data error 11 24
- = data out of range 24
- Understand Image Table 25
- Mapping and Bit/Word 25
- Descriptions 25
- ATTENTION 27
- Install the Module 28
- Mount on a Panel or Wall 30
- Description Description 31
- IMPORTANT 32
- Label here 33
- Wire the Terminal Base 34
- Connect Wiring to the FLEX 34
- I/O HART Analog Modules 34
- Terminal Base Unit 35
- Ground the Module 36
- Use Programming Software 37
- About the ControlNet and 38
- EtherNet Adapters 38
- Communication Over the 38
- FLEX I/O Backplane 38
- Scheduled Data Transfer 39
- Unscheduled Data Transfer 39
- Module I/O Mapping 39
- I/O Structure 40
- Fault State Data 40
- Device Actions 40
- Data Transfer Types 43
- Configuration Parameters 44
- Byte Order (2 of 2 bits) 47
- Examples 49
- Fault Mode (8 of 1 bit) 50
- Low Alarm Limit (8 of 16 bit) 54
- Real Time Data (RTD) 57
- Profile, Primary Input 57
- Parameters 57
- Profile, Primary Status 58
- High Alarm (8 of 1 bit each) 60
- Low Alarm (8 of 1 bit each) 60
- Loop Alarm (8 of 1 bit each) 61
- HART Status Fields 63
- Secondary Input Data 64
- Table, Cyclic EDT Input 64
- HART PV Status (8 of 8 bits): 67
- Bit 5 Reserved 68
- Bit 6 Reserved 68
- Bit 7 Reserved 68
- HART PV Status 68
- Interpret the Status 69
- Indicators 69
- Module Configuration for 69
- Little Endian Byte Order 75
- Word Swap BYTE ORDER 75
- Profile, Status Parameters 82
- Fault Alarm (8 of 1 bit each) 83
- Diagnostic Data (1 of 8 bits) 83
- Profile, Output Parameters 85
- Global Reset (1 of 1 bit) 86
- Status Indicators 87
- Configure Module Messaging 89
- HART Configuration Quick 90
- Field Value Definition 100
- HART Failed Reason Code 104
- Chapter Summary 106
- Troubleshoot Your Module 107
- FLEX I/O HART Module Commands 109
- Commands 110
- Universal Commands 110
- Common Practice 110
- Device-specific Commands 111
- Appendix 113
- Overview 113
- Message Structure 113
- Burst Mode (not supported) 114
- Start Character 115
- HART Address 115
- HART Command 115
- Byte Count 116
- Check Byte 116
- Response Code 116
- Communication 127
- HART Frame Enhancements 130
- Background Information 131
- Configuration 132
- HART Disable 133
- Channel Data Format 133
- Channel Data Formats 134
- Digital Filters 135
- High Alarm Limit 138
- Low Alarm Limit 138
- Remote High High Alarm Limit 138
- Input Map 139
- High Alarm 140
- Low Alarm 140
- Out of Range 141
- Second Alarm 141
- Diagnostic Status 141
- HART Fault 142
- HART Current Fault 142
- HART Transmitter Present 143
- Local Fault Mode 147
- Digital Mode 152
- Digital Fault Mode 153
- Analog Fault Value 153
- HART Command 3 Disable 153
- Digital Data 154
- Fault Reset 154
- Analog Data 154
- 152 Index 160
- How Are We Doing? 161
- BUSINESS REPLY MAIL 162
- Rockwell Automation 164
Verwandte Produkte und Handbücher für Ausrüstung Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog
Ausrüstung Rockwell-automation 2090-K2KSCLAMP-4 Kinetix 2000 Cable Clamp Bracket Bedienungsanleitung
(4 Seiten)
(4 Seiten)
(4 Seiten)
Ausrüstung Rockwell-automation 2707-M232P3_M485P3 DTAM Micro Operator Interface M Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Ausrüstung Rockwell-automation 57C329 Remote I/O Communications, AutoMax Bedienungsanleitung
(144 Seiten)
(144 Seiten)
Ausrüstung Rockwell-automation 6189x Integrated Display Industrial Computers User Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Ausrüstung Rockwell-automation 4100 REC Resolver to Encoder Converter Installatio Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Ausrüstung Rockwell-automation 2097-Rx Shunt Resistor Installation Instructions Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Ausrüstung Rockwell-automation 4100 ESRS Encoder Signal Reference Simulator Insta Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Ausrüstung Rockwell-automation 9528-APPOWSENE Virtual Image Templates User Manual Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Ausrüstung Rockwell-automation 2090 Ultra3000 Servo Drives Integration Manual Bedienungsanleitung
(180 Seiten)
(180 Seiten)
Ausrüstung Rockwell-automation 6181F_P Series E Integrated Display Computers Inst Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Ausrüstung Rockwell-automation 6155R 200R VersaView Industrial Non-display Comput Bedienungsanleitung
(24 Seiten)
(24 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.091 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern