Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog Bedienungsanleitung Seite 65
- Seite / 164
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Publication 1794-UM065B-EN-E - September 2010
1794-IF8IH and 1794-OF8IH Configuration 53
For this module the total Secondary Input Data Table (I) Words = 98, as
shown in the HART Input Data table..
HART Command 3 Communication Status (8 of 1 bits):
These bits indicate status of the CEDT data transfer between the adapter and
the modules. In this module the CEDT attributes transferred are HART
command 3 data for the indicated channel number.
Range: 0 = disabled or no CEDT HART Command 3 Communication error
between the adapter and the I/O module, 1= a CEDT HART Command 3
Communication error between the adapter and the I/O module.
HART Input Data
Word Bit
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0/I Reserved Ch7 Ch6 Ch5 Ch4 Ch3 Ch2 Ch1 Ch0
HART CMD 3 (Communications Status)
1 Reserved
2 Ch0 HART Field Device Status Ch0 HART Comm Status
3 Reserved FVA TVA SVA PVA Ch0 HART Loop Status
4 Ch0 HART Privary Value (IEEE 754-1985 Single-Precision 32 bit floating point)
5
6 Ch0 HART Secondary Value (IEEE 754-1985 Single-Precision 32 bit floating point)
7
8 Ch0 HART Tertiary Value (IEEE 754-1985 Single-Precision 32 bit floating point)
9
10 Ch0 HART Fourth (Quaternary) Value (IEEE 754-1985 Single-Precision 32 bit floating point
11
12 Ch0 SV Units Code Ch0 PV Units Code
13 Ch0 FV Units Code Ch0 TV Units Code
14…25 Words 2…13 for Channel 1
26…37 Words 2…13 for Channel 2
38…49 Words 2…13 for Channel 3
50…61 Words 2…13 for Channel 4
62…73 Words 2…13 for Channel 5
74…85 Words 2…13 for Channel 6
86…97 Words 2…13 for Channel 7
- Analog Modules 1
- Important User Information 2
- Summary of Changes 3
- Related Documentation 5
- Table of Contents 7
- 1794-IF8IH and 1794-OF8IH 8
- Table of Contents iii 9
- Table of Contents v 11
- What FLEX I/O Analog 13
- Modules Do 13
- Communicate with 14
- Programmable Controllers 14
- Physical Features of 15
- Your Module 15
- Use Alarms on the Input 15
- Overrange Alarm 16
- Underrange Alarm 16
- Remote Fault Alarm 16
- Local Fault Alarm 17
- Use the HART Capabilities 18
- HART Implementation 18
- Features 19
- Select Your Analog Input 20
- Module Operating Features 20
- Data Format 21
- Select Your Analog Output 22
- Latch Mode 23
- Global Reset 23
- Diagnostic Data error 11 24
- = data out of range 24
- Understand Image Table 25
- Mapping and Bit/Word 25
- Descriptions 25
- ATTENTION 27
- Install the Module 28
- Mount on a Panel or Wall 30
- Description Description 31
- IMPORTANT 32
- Label here 33
- Wire the Terminal Base 34
- Connect Wiring to the FLEX 34
- I/O HART Analog Modules 34
- Terminal Base Unit 35
- Ground the Module 36
- Use Programming Software 37
- About the ControlNet and 38
- EtherNet Adapters 38
- Communication Over the 38
- FLEX I/O Backplane 38
- Scheduled Data Transfer 39
- Unscheduled Data Transfer 39
- Module I/O Mapping 39
- I/O Structure 40
- Fault State Data 40
- Device Actions 40
- Data Transfer Types 43
- Configuration Parameters 44
- Byte Order (2 of 2 bits) 47
- Examples 49
- Fault Mode (8 of 1 bit) 50
- Low Alarm Limit (8 of 16 bit) 54
- Real Time Data (RTD) 57
- Profile, Primary Input 57
- Parameters 57
- Profile, Primary Status 58
- High Alarm (8 of 1 bit each) 60
- Low Alarm (8 of 1 bit each) 60
- Loop Alarm (8 of 1 bit each) 61
- HART Status Fields 63
- Secondary Input Data 64
- Table, Cyclic EDT Input 64
- HART PV Status (8 of 8 bits): 67
- Bit 5 Reserved 68
- Bit 6 Reserved 68
- Bit 7 Reserved 68
- HART PV Status 68
- Interpret the Status 69
- Indicators 69
- Module Configuration for 69
- Little Endian Byte Order 75
- Word Swap BYTE ORDER 75
- Profile, Status Parameters 82
- Fault Alarm (8 of 1 bit each) 83
- Diagnostic Data (1 of 8 bits) 83
- Profile, Output Parameters 85
- Global Reset (1 of 1 bit) 86
- Status Indicators 87
- Configure Module Messaging 89
- HART Configuration Quick 90
- Field Value Definition 100
- HART Failed Reason Code 104
- Chapter Summary 106
- Troubleshoot Your Module 107
- FLEX I/O HART Module Commands 109
- Commands 110
- Universal Commands 110
- Common Practice 110
- Device-specific Commands 111
- Appendix 113
- Overview 113
- Message Structure 113
- Burst Mode (not supported) 114
- Start Character 115
- HART Address 115
- HART Command 115
- Byte Count 116
- Check Byte 116
- Response Code 116
- Communication 127
- HART Frame Enhancements 130
- Background Information 131
- Configuration 132
- HART Disable 133
- Channel Data Format 133
- Channel Data Formats 134
- Digital Filters 135
- High Alarm Limit 138
- Low Alarm Limit 138
- Remote High High Alarm Limit 138
- Input Map 139
- High Alarm 140
- Low Alarm 140
- Out of Range 141
- Second Alarm 141
- Diagnostic Status 141
- HART Fault 142
- HART Current Fault 142
- HART Transmitter Present 143
- Local Fault Mode 147
- Digital Mode 152
- Digital Fault Mode 153
- Analog Fault Value 153
- HART Command 3 Disable 153
- Digital Data 154
- Fault Reset 154
- Analog Data 154
- 152 Index 160
- How Are We Doing? 161
- BUSINESS REPLY MAIL 162
- Rockwell Automation 164
Verwandte Produkte und Handbücher für Ausrüstung Rockwell-automation 1794-OF8IH FLEX Isolated Input/Output HART Analog
Ausrüstung Rockwell-automation 2090-K2KSCLAMP-4 Kinetix 2000 Cable Clamp Bracket Bedienungsanleitung
(4 Seiten)
(4 Seiten)
(4 Seiten)
Ausrüstung Rockwell-automation 2707-M232P3_M485P3 DTAM Micro Operator Interface M Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Ausrüstung Rockwell-automation 57C329 Remote I/O Communications, AutoMax Bedienungsanleitung
(144 Seiten)
(144 Seiten)
Ausrüstung Rockwell-automation 6189x Integrated Display Industrial Computers User Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Ausrüstung Rockwell-automation 4100 REC Resolver to Encoder Converter Installatio Bedienungsanleitung
(50 Seiten)
(50 Seiten)
Ausrüstung Rockwell-automation 2097-Rx Shunt Resistor Installation Instructions Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Ausrüstung Rockwell-automation 4100 ESRS Encoder Signal Reference Simulator Insta Bedienungsanleitung
(37 Seiten)
(37 Seiten)
Ausrüstung Rockwell-automation 9528-APPOWSENE Virtual Image Templates User Manual Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Ausrüstung Rockwell-automation 2090 Ultra3000 Servo Drives Integration Manual Bedienungsanleitung
(180 Seiten)
(180 Seiten)
Ausrüstung Rockwell-automation 6181F_P Series E Integrated Display Computers Inst Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Ausrüstung Rockwell-automation 6155R 200R VersaView Industrial Non-display Comput Bedienungsanleitung
(24 Seiten)
(24 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern