Rockwell-automation 1760-DNET Pico DeviceNet Communications Module Use Bedienungsanleitung Seite 32
- Seite / 168
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Publication 1760-UM003A-EN-P - September 2005
4-8 DeviceNet Functions
Change of State I/O Connection
Table 4.8 Service Code
Service Code Value Service Name Description
0E
hex
Get_Attribute_Single This service can be used to
fetch the value of a selected
attribute from the
communication module.
10
hex
Set_Attribute_Single This service can be used to
set a selected attribute in
the device.
32
hex
Extended access
(1)
(1) Additional parameters are “Time”, “Image data” and “Function block”. Addressing of the parameters is Pico
specific and is described in chapters 5 – 7 in detail.
Extended access is implemented via explicit message transfer. This transfer protocol allows the exchange of
control data. Further information about the transfer protocol can be found in section “DeviceNet
Communication profile” on page 9.
This service can be used to
address the supplementary
parameters
(1)
of the control
relay:
Table 4.9 Diagnostics Data: 2 Byte
Bytes Meaning Value Meaning
0 Pico status
(attribute ID 1)
00
hex
Static value.
1 Coupling module
status (attribute ID
2)
00
hex
The basic unit is
connected to the
1760-DNET gateway
via Pico-LINK.
04
hex
The basic unit is
either switched off
or disconnected
from the
1760-DNET gateway
via Pico-LINK.
TIP
When communication between the basic unit
Pico/GFX and the expansion unit 1760-DNET goes
down, a corresponding error code will be generated
in the third data byte. Furthermore, the Rx/Tx data of
the gateway will be transferred with the value 00hex.
- Pico DeviceNet 1
- Communication 1
- Interface 1
- Important User Information 2
- Table of Contents 3
- Table of Contents 2 4
- Who Should Use this 5
- Purpose of this Manual 5
- Common Techniques Used 6
- Preface 4 8
- Pico DeviceNet Interface 9
- Structure of the Unit 10
- Communication Profile 10
- Hardware and Operating 10
- System Requirements 10
- Use Other Than Intended 11
- Installation 13
- Connect the Power Supply 14
- DeviceNet 14
- EMC Compatible Wiring 15
- Potential Isolation 16
- Data Transfer Rates – 16
- Automatic Baud Rate 16
- Recognition 16
- • or Flat Cable 17
- 2-6 Installation 18
- Initial Power On 19
- DeviceNet Setting the 19
- Slave Address 19
- With Pico-SOFT, version 3.1 21
- LED Status Displays 22
- Cycle Time of the Pico 23
- Basic Unit 23
- EDS File 23
- IMPORTANT 24
- DeviceNet Functions 25
- Management Objects 26
- Connection Objects 27
- Manufacturer-Specific Objects 28
- Identity Object 28
- Service Code 29
- DeviceNet Object 30
- Pico Object 30
- DeviceNet Communication 33
- General Method of Operation 34
- I/O Connection) 37
- Input data: 38
- Mode, S1 to S8 38
- Output Data: 40
- Mode, R1 – R16 40
- 0 = status ’0’ 1 = status ’1’ 42
- Value 19hex = 0001 1001bin: 42
- Enable R13, R12 and R9 42
- Application Examples for Pico 45
- Read/Write Date and Time 46
- Switching Rule Bit Array 47
- Read/Write Image Data 48
- A1 – A16 49
- Counters: C1 to C16 50
- Possible causes page 6-34 51
- Local inputs: I1 – I16 52
- (Low Byte first) 53
- (1) 02 = Analog input I11 54
- (2) Possible causes page 6-34 56
- (1) Possible causes page 6-34 57
- Local P buttons: P1 – P4 58
- Local outputs: Q1 – Q8 59
- Timers: T1 – T16 61
- Year time switch: Y1 – Y8 62
- Master reset: Z1 – Z3 63
- 7-day time switch: 63
- Counter relays: C1 – C16 67
- Example: 70
- Data 1 (Byte 4) = 0x01 70
- Meaning: 70
- Timing relays: T1 – T16 71
- Data 1 (Byte 4) = 0xAC 72
- Channel A, index 11/12 75
- Pico GFX Control Commands 81
- Version history 82
- Read/write date and time 82
- Winter/summer time, DST 84
- Switching rule bit array 85
- Read/write image data 87
- Local diagnostics: ID1 – ID16 89
- Read local inputs: IW0 90
- Marker: M 92
- ATTENTION 93
- Example 2: Write marker word 94
- Local analog output: QA1 96
- Local outputs: QW0/ 97
- Send data network: SN1 – SN32 99
- Read/write function block 100
- Overview 101
- High Byte) 103
- Block Compare: BC01 – BC32 105
- Block Transfer: BT01 – BT32 107
- Counter: C01 – C32 110
- Comparator: CP01 – CP32 116
- Data block: DB01 – DB32 120
- PID controller: DC01 – DC32 121
- Example 127
- Year time switch: HY01 – HY32 129
- Value scaling: LS01 – LS32 131
- Master reset: MR01 – MR32 132
- Hours-run meters: OT01 – OT04 135
- Timing relays: T01 – T32 141
- Value limitation: VC01 – VC32 143
- Analysis – error codes via 144
- PicoLink 144
- Troubleshoot Your Controller 147
- Specifications 149
- A-2 Specifications 150
- Specifications A-3 151
- Dimensions 152
- Glossary 153
- Glossary 2 154
- Glossary 3 155
- Glossary 4 156
- Glossary 5 157
- Glossary 6 158
- Glossary 7 159
- Glossary 8 160
- Glossary 9 161
- Glossary 10 162
- Glossary 11 163
- Glossary 12 164
- 2 Index 166
- Index 3 167
- Rockwell Automation 168
Verwandte Produkte und Handbücher für Ausrüstung Rockwell-automation 1760-DNET Pico DeviceNet Communications Module Use
Ausrüstung Rockwell-automation 1760-xxxx Pico GFX-70 Controllers User Manual Bedienungsanleitung
(400 Seiten)
(400 Seiten)
Ausrüstung Rockwell-automation 1793-OV16 Flex Integra Output Module Install Inst Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Ausrüstung Rockwell-automation 1792D-CB18PT ArmorBlock MaXum I/O Cable Bases Seri Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Ausrüstung Rockwell-automation 1769-IA16 Compact 1769-IA16 120V ac Input Module Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Ausrüstung Rockwell-automation 1790-XXXX CompactBlock LDX I/O DeviceNet RTD and T Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Ausrüstung Rockwell-automation 1784-U2DHP USB-to-Data Highway Plus Cable Installa Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Ausrüstung Rockwell-automation 1756-DHRIO_DHRIOXT ControlLogix Data Highway Plus- Bedienungsanleitung
(176 Seiten)
(176 Seiten)
Ausrüstung Rockwell-automation 1792-IB16LP INSTL INSTR 16 INPUT MODULE Bedienungsanleitung
(10 Seiten)
(10 Seiten)
Ausrüstung Rockwell-automation 1766-L32xxx MicroLogix 1400 Programmable Controlle Bedienungsanleitung
(45 Seiten)
(45 Seiten)
Ausrüstung Rockwell-automation 1792D-OB4D ArmorBlock MaXum 8 Output Module Series Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Ausrüstung Rockwell-automation 1769-IA8I Compact Individually Isolated 120V ac In Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Ausrüstung Rockwell-automation 1746-HSTP1 Stepper Controller Module/ User Manual Bedienungsanleitung
(82 Seiten)
(82 Seiten)
Ausrüstung Rockwell-automation 1747-SDN 1747-SDN DeviceNet Scanner Installation I Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Ausrüstung Rockwell-automation 1732D-XXXX DeviceNet ArmorBlock I/O, Series A Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Ausrüstung Rockwell-automation 1788-CN2FF ControlNet-to-FOUNDATION Fieldbus H1 Li Bedienungsanleitung
(56 Seiten)
(56 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern