Rockwell-automation 1746-NR4 SLC RTD/Resistance Input Module User Manu Bedienungsanleitung Seite 101
- Seite / 148
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Publication 1746-UM008B-EN-P - December 2006
Module Diagnostics and Troubleshooting 101
The LED Indicator Status Description table explains the function of the
channel status LED indicators while the module status LED indicator is
turned on.
The Module Status LED Indicator State table explains the function of
the module status LED indicator.
I/O error codes are reported in word S:6 of the SLC processor status
file. The characters denoted as XX represent the slot number (Hex) for
the module. The characters denoted as YY represent the 2-digit hex
code for the fault condition.
The format for the error codes in the status word (S:6) is shown in the
Error Code Format diagram on page 102.
LED Indicator Status Description
If Module
Status LED
Indicator is
And Channel
Status LED
Indicator is
Indicated Condition Corrective Action
On On Channel enabled No action required.
Flashing Broken Input Condition
(open circuit for RTD or
resistance input, and
short circuit for RTD
inputs only)
To determine the exact
error, check the error bits
13…15 in the input image.
Check the channel
configuration word for
valid data. Make sure that
the input type is indicated
correctly in bits 0…3.
Refer to the
troubleshooting flowchart
on page 7-6 and chapter 5
for more information.
Out-of-range Condition
Channel Configuration
Error
Off Power-Up No action required.
Channel Not Enabled No action required. For an
example of how to enable
a channel refer to chapter
6, Ladder Programming
Examples.
Module Status LED Indicator State
If Module
Status LED
Indicator is
Indicated Condition Corrective Action
On Proper Operation No action required.
Off Module Fault Cycle power. If condition persists, replace the
model or call your local distributor or
Allen-Bradley for assistance.
- SLC 500 1
- RTD/Resistance 1
- Input Module 1
- Important User Information 2
- Summary of Changes 3
- New Information 3
- 4 Summary of Changes 4
- Table of Contents 5
- 6 Table of Contents 6
- Use This Manual 7
- Who Should Use This 7
- Purpose of This Manual 7
- Contents of this Manual 8
- Common Techniques Used 9
- 10 Preface 10
- Overview 11
- 12 Overview 12
- RTD Compatibility 13
- 14 Overview 14
- Overview 15 15
- Hardware Overview 16
- System Overview 18
- System Operation 19
- LED Indicator Status 20
- 22 Overview 22
- Quick Start Guide 23
- Procedures 24
- Insert the Module 25
- Wire the Module 25
- Configure Your I/O 28
- Output Image Detail 29
- 30 Quick Start Guide 30
- Input Image Detail 31
- Monitoring Status 32
- Install and Wire the Module 33
- NR4 Power Requirements 34
- Module Location in Chassis 35
- General Considerations 37
- Module Installation and 38
- Install the Module 39
- Remove the Module 39
- Terminal Wiring 40
- IMPORTANT 41
- Cable Examples 46
- Calibration 47
- Single-point Calibration 48
- Module ID Code 51
- Module Addressing 52
- O : 4 . 2 53
- I : 3 . 6 53
- Channel Filter Frequency 54
- Selection 54
- Effective Resolution 55
- 10 Hz Filter Notch Frequency 56
- 50 Hz Filter Notch Frequency 57
- 60 Hz Filter Notch Frequency 57
- 250 Hz Filter Notch Frequency 57
- Scanning Process and 58
- Channel Timing 58
- Scanning Cycle 60
- Channel Turn-on, Turn-off 61
- Response to Slot Disabling 61
- Input Response 62
- Output Response 62
- Procedure 64
- Enter the Configuration Data 65
- Scaled–for–PID 68
- Temperature Counts 69
- -200 °C (-328 °F) -32,768 69
- +630 °C (1166 °F) +32,767 69
- Scaling Examples 71
- 1746-NR4 73
- Scaling Select (Bits 13-14) 78
- User-set Scaling 79
- Limit Scale Words 80
- Channel Data Word 81
- Channel Status Checking 82
- Bits Define 83
- These bit settings 83
- Indicate this 83
- 1514131211109876543210 83
- Input Type Status (Bits 0…3) 84
- Excitation Current (Bit 12) 85
- Broken Input Error (Bit 13) 85
- Out-of-range Error (Bit 14) 86
- Configuration Error (Bit 15) 86
- Ladder Programming Examples 87
- Initial Programming 88
- Configuration Word Setup 89
- Copy File Data Flow 89
- Programming Procedure 90
- Dynamic Programming 91
- Verify Channel 92
- Configuration Changes 92
- Interface to the PID 93
- Instruction 93
- Use the Proportional 95
- Counts Data Format with 95
- Monitor Channel Status 96
- Invoke Autocalibration 97
- Introduction 99
- Module Operation vs 99
- Channel Operation 99
- Power Turn-on Diagnostics 100
- Channel Diagnostics 100
- LED Indicators 100
- Error Codes 102
- Out-of-range Detection 103
- Troubleshooting Flowchart 105
- Replacement Parts 106
- Contact Rockwell 106
- Automation 106
- Application Examples 107
- Channel Configuration 108
- Program Listing 109
- Program to Convert °F to BCD 110
- Supplementary Example 111
- Degrees Selector Switch 114
- Specifications 117
- 118 Specifications 118
- Module Accuracy 119
- 120 Specifications 120
- Specifications 121 121
- 122 Specifications 122
- RTD Standards 123
- 124 RTD Standards 124
- Configuration Worksheet 125
- I/O Configuration 131
- 132 I/O Configuration 132
- I/O Configuration 133 133
- 6. Click OK 134
- Glossary 135
- 136 Glossary 136
- Glossary 137 137
- 138 Glossary 138
- 140 Index 140
- Index 141 141
- 142 Index 142
- How Are We Doing? 143
- BUSINESS REPLY MAIL 144
- Rockwell Automation 148
Verwandte Produkte und Handbücher für Ausrüstung Rockwell-automation 1746-NR4 SLC RTD/Resistance Input Module User Manu
Ausrüstung Rockwell-automation 1757-FIMRTP ProcessLogix Remote Termination Panel Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Ausrüstung Rockwell-automation 1734-IK/C POINT I/O 5V and 24V Encoder/Counter Mod Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Ausrüstung Rockwell-automation 1756-OF8I ControlLogix Eight-channel Isolated Anal Bedienungsanleitung
(208 Seiten)
(208 Seiten)
Ausrüstung Rockwell-automation 1747-L40 SLC 500 Fixed Hardware Style Bedienungsanleitung
(223 Seiten)
(223 Seiten)
Ausrüstung Rockwell-automation 1762-OV32T MicroLogix Solid State 24V DC Sink Outp Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Ausrüstung Rockwell-automation 1766-Lxxxx MicroLogix 1400 Programmable Controller Bedienungsanleitung
(406 Seiten)
(406 Seiten)
Ausrüstung Rockwell-automation 1769-IT6 Compact I/O 1769-IT6 Thermocouple/mV Inpu Bedienungsanleitung
(168 Seiten)
(168 Seiten)
Ausrüstung Rockwell-automation 1792-IB8XOB8PLP INSTL INSTR ARMORBLOCK LP 8/8 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Ausrüstung Rockwell-automation 1792-IB4/B INSTL.INST ARMORBLOCK 4 INPUT Bedienungsanleitung
(36 Seiten)
(36 Seiten)
Ausrüstung Rockwell-automation 1747-PBASE BASIC Development Software Programming Bedienungsanleitung
(144 Seiten)
(144 Seiten)
(1 Seiten)
Ausrüstung Rockwell-automation 1746-NT4 SLC 500 Thermocouple/mV Input Module Inst Bedienungsanleitung
(24 Seiten)
(24 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern