Rockwell-automation 1734-OX2/C POINT I/O 2 Relay Output Module Bedienungsanleitung

POINT I/O is a trademark of Rockwell AutomationDeviceNet is a trademark of ODVA, Inc. Publication 1734-IN587B-EN-P - March 2002Installation Instructi

10 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002Wiring the Relay Output ModuleATTENTION!Relay contacts are not powe

POINT I/O 2 Relay Output Module 11Publication 1734-IN587B-EN-P - March 2002Channel Output Relay Common Supply0 (N.C.) 0460 (N.O.) 21 (N.C.) 157

12 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002Channel Output Relay CommonSupply10 (N.C.) 0460 (N.O.) 21 (N.C.) 15

POINT I/O 2 Relay Output Module 13Publication 1734-IN587B-EN-P - March 2002ATTENTION!• Do not attempt to increase load current or wattagecapabi

14 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 200201 01 0101 0101010124VL1120V/240V ac42010ltL2/NWiring using externa

POINT I/O 2 Relay Output Module 15Publication 1734-IN587B-EN-P - March 2002Troubleshooting with the IndicatorsModule StatusOff No power applied

16 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002Indicator Indication Probable CauseNetwork StatusOff Device is not

POINT I/O 2 Relay Output Module 17Publication 1734-IN587B-EN-P - March 2002Safety ApprovalsThe following information applies when operating thi

18 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002SpecificationsSpecifications - 1734-OX2 Output Relay ModuleOutputs

POINT I/O 2 Relay Output Module 19Publication 1734-IN587B-EN-P - March 2002Fusing Module outputs are not fused. If fusing is desired, you must

2 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002This Series C product can be used with DeviceNet and PROFIBUS adapte

Publication 1734-IN587B-EN-P - March 2002 PN 957657-97Supersedes 1734-IN587A-EN-P - December 2001 © 2002 Rockwell International Corporation. Printed i

POINT I/O 2 Relay Output Module 3Publication 1734-IN587B-EN-P - March 2002WARNING!Identifies information about practices or circumstances that

4 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002ATTENTION!Environment and EnclosureThis equipment is intended for us

POINT I/O 2 Relay Output Module 5Publication 1734-IN587B-EN-P - March 2002WARNING!EXPLOSION HAZARD• Do not disconnect equipment unless power ha

6 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002Installing the Mounting BaseTo install the mounting base on the DIN

POINT I/O 2 Relay Output Module 7Publication 1734-IN587B-EN-P - March 20023. Insert the module straight down into the mounting base and press t

8 POINT I/O 2 Relay Output Module Publication 1734-IN587B-EN-P - March 2002Removing a Mounting BaseTo remove a mounting base, you must remove

POINT I/O 2 Relay Output Module 9Publication 1734-IN587B-EN-P - March 2002Communicating with Your ModuleI/O messages are sent to (consumed) and